The Next Generation of Inertial sensors are here
Introducing the NEW, lower noise, higher speed , next-generation SX2 Inertial sensors. Through the combination of ultra-low ARW, improved bias performance and enhanced VELOX™ Processing features, our SX2 product line offers performance previously reserved for larger systems in each of our products smaller than 0.7 cubic inches, enhancing our technical offering while maintaining the SWaP-C advantage of our low noise MEMS sensors. The technical advancement in the SX2 product line further establish Gladiator inertial sensors as the premier MEMS choice for precision stabilization applications.
Low Noise.
0.0016°/s/√Hz
Ultra Low ARW
High Speed.
Speed matters when it comes to stabilization. VELOX™ processing technology employs advanced rapid sampling and signal processing techniques to output data at high speed with minimal phase lag. You won’t find anything faster.
And now, VELOX™ processing advances to a new level with the SX2 product line and new features enabled through VELOX™ Plus.
Key performance improvements allow users to define higher bandwidths, data rates and baud rate driving digital message delay to as low as 100µs. Product improvements include an 8x increase in gyroscope resolution and a 4x increase in accelerometer resolution to further establish Gladiator inertial sensors as the premier MEMS choice for precision stabilization applications.
Stable Performance
Repeatable performance is a critical element of precision control loop applications. After 50 years in the industry, our product designers have seen hundreds of commercial and defense application requirements and been through rigorous qualification processes – committing to more stable performance in harsher environments. The SX2 inertial sensors realize advancements in bias stability and performance through shock and vibration.
Gladiator Technologies calibrates and models all products in the factory to assure repeatable and predictable performance over the full temperature range -50°C to 85°C. In addition, our sensors are subject to an extensive conditioning period over temperature, shock and vibration to assure repeatability.
SX2 Products
G300D Triax Gyro
The G300D is Gladiator Technologies’ high speed, three-axis MEMS gyroscope equipped with low noise sensors, VELOX™ high speed processing and user configurable firmware. At only 0.6 cubic inches, the G300D gyro comes factory calibrated over the full temperature range, conditioned over environments and is ideal for precision stabilization and rotation measurement applications.
490°/s Rate Range
0.6
Cubic Inches
0.0017°/s/√Hz
ARW
0.075°/s
Bias Over Temperature
600Hz
Bandwidth
10kHz
Data Rates
<57µs
Message Delay
LandMark™005 IMU
Low noise, high speed, six-axis IMU.
490°/s Gyroscopes
15g Accelerometers
0.6
Cubic Inches
0.0017°/s/√Hz
ARW
0.075°/s
Bias Over Temperature
600Hz
Bandwidth
10kHz
Data Rates
<29µs
Message Delay
LandMark™007 IMU
2000°/s Gyroscopes
98g Accelerometers
2000°/s
Rate Range
0.0025°/s/√Hz
ARW
0.075°/s
Bias Over Temperature
98g
Accel Range
10kHz
Data Rates
<114µs
Message Delay
LandMark™007X IMU
High Dynamic 6 Axis IMU
The LandMark™007X IMU is Gladiator Technologies’ high speed, six-axis MEMS Inertial Measurement Unit (IMU) built for high dynamic environments. This IMU is equipped with low noise sensors and VELOX™ high speed processing and user configurable firmware. Only 0.7 cubic inches, the LandMark™007X comes factory calibrated over the full temperature range, conditioned over environments
2000°/s Gyroscopes
200g Accelerometers
2000°/s
Rate Range
0.0017°/s/√Hz
ARW
0.075°/s
Bias Over Temperature
200g
Accel Range
10kHz
Data Rates
<114µs
Message Delay
A300D Accelerometer
High Dynamic 3 Axis digital accel.
The new A300D is Gladiator Technologies’ ultra-low noise three axis MEMS accelerometer with high dynamic range sensors. At only 0.6 cubic inches, the A300D accelerometer comes factory calibrated over the full temperature range, conditioned over environments.
0.058 mg /√Hz
VRW
0.5 mg
Bias Over Temperature
Message Delay
0.6
Cubic Inches
Bandwidth
G300D Triax Gyro
The G300D is Gladiator Technologies’ high speed, three-axis MEMS gyroscope equipped with low noise sensors, VELOX™ high speed processing and user configurable firmware. At only 0.6 cubic inches, the G300D gyro comes factory calibrated over the full temperature range, conditioned over environments and is ideal for precision stabilization and rotation measurement applications.
0.6
Cubic Inches
0.0017°/s/√Hz
ARW
0.075°/s
Bias Over Temperature
600Hz
Bandwidth
10kHz
Data Rates
<20µs
Message Delay
LandMark™005 IMU
0.6
Cubic Inches
0.0017°/s/√Hz
ARW
0.075°/s
Bias Over Temperature
600Hz
Bandwidth
10kHz
Data Rates
<29µs
Message Delay
LandMark™007X IMU
The LandMark™007X IMU is Gladiator Technologies’ high speed, six-axis MEMS Inertial Measurement Unit (IMU) built for high dynamic environments. This IMU is equipped with low noise sensors and VELOX™ high speed processing and user configurable firmware. Only 0.7 cubic inches, the LandMark™007X comes factory calibrated over the full temperature range, conditioned over environments
200g
Accel Range
2000°/s
Rate Range
10kHz
Data Rates
0.002°/s/√Hz
ARW
<115µs
Message Delay
0.075°/s
Bias Over Temperature
LandMark™007 IMU
The LandMark™007 IMU is Gladiator Technologies’ high speed, six-axis MEMS Inertial Measurement Unit (IMU) built for high dynamic environments. This IMU is equipped with low noise sensors and VELOX™ high speed processing and user configurable firmware. Only 0.7 cubic inches, the LandMark™007 IMU comes factory calibrated over the full temperature range, conditioned over environments
98g
Accel Range
2000°/s
Rate Range
10kHz
Data Rates
0.0025°/s/√Hz
ARW
<114µs
Message Delay
0.075°/s
Bias Over Temperature
A300D Accelerometer
The new A300D is Gladiator Technologies’ ultra-low noise three axis MEMS accelerometer with high dynamic range sensors. At only 0.6 cubic inches, the A300D accelerometer comes factory calibrated over the full temperature range, conditioned over environments.
Sensor Range
Message Delay
0.6
VRW
800Hz
0.5 mg
Bias Over Temperature